RAM-Security
RAM-Security Intruder Alarms & Cctv Systems Installations - Repairs - Upgrades - Maintenance Based in Stockton-on-Tees covering the North East region Call : 0843 523 1073 Email :...
View ArticleTexecom Veritas R8 keypad malfuntioning
I have a Veritas R8 installed during 2001/2, with a keypad near front door, I replaced the lead acid battery in July 2012. Yesterday I found that I can't input my code. Some of the numbers make no...
View ArticleScantronic 9651 - 2 problems
We were having some work done on our kitchen and the wire for our alarm keypad and one of the motion detectors was cut. Thankfully, the alarm didn't sound as this was late last night. This morning I...
View ArticleZone Tamper
Hi. I'm a bit stuck. I have a Scantronic 9751 system with 9940 remote keypad. A few weeks ago the batteries on my wireless motion detectors needed changing, which I did. I did and engineer reset but I...
View ArticleScantronic 9651 wire cut
We were doing some DIY and accidentally cut the wire for our alarm keypad and one of the sensors. The alarm didn't sound or anything - the panel and sensor above it just didn't have any power. It was...
View ArticleProx SA
I`m having problems finding a Pyronix Prox SA programing Manual .Can anypne help please
View ArticleAvanti LC
Hi, I don't know if anyone can help me out here...I've finally got around to installing an Avanti LC (with LCD RKP) system in our home (It's been sat in a box for 3 years!) I have the 'Engineer's...
View ArticleScantronic 500r+
I installed a Scantronic 500r+ wireless control panel + PIR's probably 15 to 20 years ago. I have a AG6 external bell + strobe unit hard wired. The system has worked reliably since day one then about a...
View Articlegardtec 500 a/c
Im new to the web site. And was wondering if someone can help me with my alarm system a G-Tec 500 i think the thing has been timer programmed by the engineer to log me out of the system. I do not have...
View ArticleClik here to view.
Tamper circuit wiring question
Good Evening. I am going to be fitting an alarm for a friend, and I wish to use the existing bell box from the previous system that was fitted. The bell box is a Pyronix Belle, and the new control...
View ArticlePA button with resistor fitted
I would like to ask the following question and get some advice please if I may? In my friend's house where I am fitting an alarm, there is an old existing PA button which has a 2K2 EOL resistor fitted...
View ArticleCastle euro mini programing manual
Hi Need to relocate a keypad on a Castle Care-tech euro mini panel. By any chance does anybody have a programing manual for this panel as unfortunately this is not the most popular panel on the market....
View ArticleKeypad for Scantronic 9454
I need help in getting hold of a replacement keypad for a Scantronic 9454 burglar alarm. Any help would be appreciated. Thanks
View ArticleAccenta Mini Gen 4 - some questions
Good afternoon. I would like to request some help please if I may? I am going to be fitting an alarm for a friend, and I wish to use the existing bell box from the previous system that was fitted. The...
View ArticleScantronic 9651 Missing Battery problems
Just joined this forum as I need your help with sorting out my scantronic 9651 zone alarm. I noticed your replies to some of the other members of this forum and that's why I thought maybe you could...
View ArticleLid tamper message 9930 keypad
12months ago we had the alarm system (9651) disconnected then reconnected whilst we had building works. No error message showed but we could not set the alarm. The spanner light glows red; the "wave"...
View Articlealarm not working after mains electric turned off
Hi i turned my mains electricity off and when i switched it back on the alarm isn't working,there is a green light lit up on the unlocked padlock symbol,can anyone help me fix this issue? Many thanks...
View Articlescantronic 9427 keypad not working after switching mains electricity back on
Hi i am having a problem with my alarm its a scantronic 9427 keypad,the unlocked padlock sign is lit up with a green light,can anyone help me this this? Thanks Graeme
View ArticleCooper Menvier Scantronic 9651 - K01 reset
Hi, hoping someone can help me! We moved into our new house and the alarm is a cooper Menvier Scantronic 9651. My husband unscrewed the lid on the control box (he had a "moment" and did not realize it...
View ArticleAdvantage zx - tripped fuse - alarm malfunction
While I was away, a decorator tripped the main fuse in the house by getting water into the electrics of a wallpaper stripper. When we turned the power back on, the alarm went off and wouldn't allow us...
View Article
